Check to see if you need to update the modem's firmware. Download the latest firmware for the C 1100T. Tip: If the firmware link doesn't work, try another browser (Chrome is known to have issues with this kind of link). Or, right-click the link, select "copy link address", then paste the link into a new browser tab. Click "Start" on the computer plugged in (or connected through a router or switch) to the modem. Step 2 Click "Programs" and open your Internet browser of choice.
A more standard approach would be to connect the two routers together behind the modem. One of the following configurations. You could connect router A into the modem as normal and connect WAN from router B into A. This requires B to have a different network configured ( they both canā€™t be 192.168.1.x).
I have a Voice and Data Modem TECHNICOLOR CGM4140COM. It has two ports. One I use for my mobile network extender. Into the other port, I would like to connect 2 notebook PCs using ethernet cables to connect to the Internet. One is my personal PC. The other notebook I use for work. I plugged a Netgear Fast Ethernet Switch FS605 v2 into the modem. Right Click Start Menu 2. Click Windows PowerShell/Command Prompt (Admin) 3. type in "netsh winsock r" (without quotes), press enter 4. Restart PC. Sometimes doing a winsock reset will help webpages load again. It's a rare occurrence but sometimes necessary.
Note that the value of ā€œ1ā€ means ā€œmodem modeā€ (also known as ā€œbridge modeā€), while ā€œ2ā€ means ā€œordinary NAT+routing modeā€. Be very careful. Turning on ā€œmodem modeā€ breaks Wi-Fi. You may need to bring up a separate access point for Wi-Fi. You may have trouble restoring the setting.
Plug the cable modem power cord into any 120V AC wall outlet. Wait five minutes until the modem has a solid green Online light on the front of the device. (If the green light doesnā€™t come on, please try another cable outlet.) Connect the supplied Ethernet cable to either a PC, router or eero device and power it up.
From the submenu on the left select Connection. From the next submenu select Wi-Fi. Select ā€œeditā€ next to the network you wish to change the encryption type for contained within ā€œPrivate WiFi Networkā€.
But then I decided to still try connect the disconnected cable (cat.5 FT4) to Xbox, and holy crap, it works! So I don't know, I wouldn't have guessed one cable is not working in one part of the chain of cables, but does work in another. So thanks again! Edit. Okay so the wire that was previously connected to Xbox has some connection problems. First, screw one end of the coax cable into an active cable outlet (try the same outlet where your previous Cox device was connected) and the other end into the coax port on the back of your Panoramic Wifi Gateway. Then, plug the power cord into an electrical outlet and the other end into the power port on the back of your Panoramic Wifi Step 2 Connect your Network. 1. Connect the WAN port of the router to the LAN port of your DSL modem with Ethernet cable. 2. Connect the phone line (DSL Line) to the Line port of your DSL modem. 3. Connect your computer to one LAN port of your TP-Link router. Step 3 to the web management page.
Gold Coast. Hey all, For those unaware, after the 0.11 firmware update to the Arcadyan LH1000 variant of the Telstra Gen 2 Smart Modem, they were unable to be modified to be an Access Point. However - after much trial and error, I have successfully figured out a way for it to be done. The reason I put the guide together was because the Gen 2
Ignite HomeConnect app using your MyRogers username and password. If the Get Started screen does not appear right away, select the Activate Ignite WiFi Gateway. Wait about 5 minutes for the setup to finish. Within 5 minutes, the light on your Gateway should flash and turn orange, then green, then turn either solid or blinking white.
I mean 4 primary partitions on your usb hard drive, I assume your c: drive will be in your computer and contains your operating system. I have 2 x 2TB hard drives connected to my TP-LINK TD-W8970 router, both have just the one primary partition for the whole hdd, formatted to ntfs.
APC UPS Battery Backup (600VA) Keep your modem, router, and hubs juiced, with a port to charge your phone. $79 at Amazon. If you have a more complex setup with multiple pieces of network gear such as a Power over Ethernet (PoE) switch, and/or you have a Network Attached Storage (NAS) device like a Synology NAS tucked in with your network gear
Cannot connect wirelessly after your NETEGAR cable gateway is connected to MediaCom service; Cable gateway shows only Cable Connection page on the BASIC tab. Cable gateway shows only Administration options on the ADVANCED tab. Wireless functionality on the cable gateway is disabled. Router mode setting is set to NO or dimmed. POWER - Connects the power cord to the modem. WPS - Located on the top of the modem, this button can be used instead of entering the WiFi password to connect wireless devices that support WPS to the Technicolor CGM4141. WPS works only for wireless networks that use passwords encrypted with the WPA Personal or WPA2 security protocols.

Solution. #10. This is the source of the confusion. USB is not HDMI. I doubt there is any way to use a USB port to hook to a tv. You can hook up things like roku or a memory stick but I have never seen a tv that supports hooking up a router. The USB port on a router in most cases is only used to hook up stuff like hard drives or in some cases

Complete the following steps. From the Gateway, click the Wireless tab. In the Wireless section, click the Security tab. 7. From the Security tab, complete the following steps to change the WiFi password. From the Security Mode drop-down menu, select Open (risky), WPA2 Personal, or WPA or WPA2 Personal. .